Продукция

Heater folgirovanny: IZOLAR-F, IZOLAR-LM

 

zolar-F –the made foam polyethylene duplicated by an aluminum (AL) foil. Thanks to high heat-insulating properties it is widely applied where house thermal insulation with high efficiency, the minimum expenses is necessary and at the minimum thickness of an insulating layer.


Izolar-LM – the made foam polyethylene duplicated by a mylar film with the metallized covering. The metallized film (lavsan) is applied in systems "Heat-insulated floors" since isn't affected by alkaline cement mortars. While the foil collapses at interaction with a cement coupler.

Reflects to 97% of infrared radiation, working by the principle of a thermos.

allows to reduce the volume of construction designs of walls, floors and a roof without loss of heattechnical characteristics.

it is easy-to-work also to installation.
.

 

 



Scope Izolar NPE

Izolar -LM, Izolar-F —the universal heat-insulating material which main function is reflection of heat, and also protection against moisture, water and noise. Izolar-LM, Izolar-F allows at a small thickness and the minimum heatloss (the principle of a thermos) in the summer considerably to reduce an overheat under a roof, and not to pass cold air inside in the winter and not to let out warm outside. Izolar-LM, Izolar-F – thanks to the universal properties, opens unlimited opportunities of the use:

Cautions:
- Not to establish the made foam polyethylene near naked flame.
- Not to stack the made foam polyethylene on the chemical processed wooden surfaces before their full drying.
- Not to use the made foam polyethylene outside temperature condition: from –50 °C to +80 °C. Short-term use in temperature condition to +95 ° is allowed.
- Use of the made foam polyethylene in the open air on condition of full protection against hit of direct sunshine is allowed.

 

1. Isolation in Heat-insulated floor system


the recommended thickness: the 4-5mm

 

Plate overlapping

Izolar-LM keeps within the reflecting party up. Joints of material connect the metallized adhesive tape.

Heating element

Cement coupler

Floor covering

 

Additional benefits of Izolar-LM:
- protects the room from moisture of the first floor
- speed of heating of a floor increases
- heat from a heater is distributed more evenly
- heating of a ceiling and the cellar from below is excluded


2. The warmed roof, penthouse, roof, attic


4-5мм ҡалынлыҡ тәҡдим ителә

Internal finishing: gypsum cardboard, lining, plastic panels

Counterlath (wooden)
Provides an air gap 1,5-2sm between isolation Izolar-LM (Izolar-F) and internal finishing.

Izolar-LM, Izolar-F is established on a wooden roofing battens of a design of a roof (on rafters) the reflecting party in the room. It is fixed by means of the construction stapler, small nails or self-tapping screws. Installation is conducted from below up by horizontal panels with joints not less 10sm. Joints connect the metallized (foiled ) adhesive tape.

Heater: minvata, expanded polystyrene, polyfoam

Rafter

Izolar And, Izolar AM - a vapor-permeable membrane for protection of a heater against external moisture.

Subpurlin or a continuous board flooring fastens on counterlaths.

Roofing material


4-5мм ҡалынлыҡ тәҡдим ителә

Эске эштәр: гипсокартон, вагонка, пластик панельдәр

Контррейка (ағастан)
Изолар-ЛМ (Изолар-Ф) менән эске эштәр араһында 1,5-2см һауалы ара тәьмин итә

Изолар-ЛМ, Изолар-Ф – ҡыйыҡтың ағас конструкцияларына (стропилдарға) кире
ҡайтарыу яғы менән бина эсенә ҡаратып беркетелә. Тѳҙѳлѳш степлер, ваҡ сѳйҙәр
йәки саморез ярҙамында бкркетелә. Горизонталь таҫма аҫтан ѳҫкә ҡорола,
тоташҡан урындары (стыктары) 10 см-ҙан кәм булмаһын.
Металлаштырылған (фольга менән ҡапланған) скотч менән ялғана.

Йылытҡыс: минвата, пенополистирол, пенопласт

Стропило (асамай )

Изолар А, Изолар АМ - тышҡы дымдан һаҡлаусы пар үткәреүсе мембрана

Обрешетка йәки тигеҙ таҡта түшәм контррейкаға нығытыла.

Түбә материалы

 


3 Frame wall



the recommended thickness: the 4-10mm

Internal finishing of a wall

Counterlath. (wooden). Provides an air gap 1,5-2sm between isolation Izolar-LM (Izolar-F) and internal finishing.

Izolar-LM, Izolar-F - Installation directly on the basis of a wall
protection, on a usual heater and frame designs. It is fixed to a framework
by wooden laths, when finishing by gypsum cardboard – galvanized profiles.
Installation is conducted from below up by horizontal panels with joints
not less 10sm. Joints connect the metallized (foil) adhesive tape.
For a competent noise isolation the allowance of materials for joints
of other wall and roofing designs becomes.
Except effect of reflection Izolar-LM (Izolar-F) doesn't allow particles
of a heater to get in the room.

Heater: mineral wool, expanded polystyrene, polyfoam

framework

Izolar And, Izolar AM - a vapor-permeable membrane for protection of a heater against external moisture.


4. Floor first floor


the recommended thickness: the 3-10mm

Plate overlapping

Izolar C, Izolar D - the waterproofing film protecting a heater from moisture of the first floor.

Wooden logs

Heater: mineral wool, expanded polystyrene, polyfoam

Izolar-LM, Izolar-F keep within the reflecting party in the room. Joints of material connect the metallized (foil) adhesive tape. Fixing of material is carried out by a counterlath by means of self-tapping screws, in addition providing an air gap between a draft floor and a heater.

Counterlath. Provides a ventilating gap between a draft floor and a heater and fastens to wooden beams self-tapping screws.

Draft floor (board)

Besides the reflecting effect Izolar-LM (Izolar-F) protects a heater from moisture.



5. Warm balcony


the recommended thickness: the 4-10mm



6. Warming of hangars, warehouses, garages


the recommended thickness: the 5,8,10,20,50 mm



7. Isolation of air ducts in systems of ventilation

the recommended thickness: the 5, 8, 10mm



8 Screens behind heating radiators

 


the recommended thickness: the 2, 3 mm


As researches show, losses of heat through a radiator area site of an external
wall considerably surpass losses of heat through the next sites of a wall.
The most effective remedy for decrease in thermal losses is fastening to a surface of a
zaradiatorny site of the heat reflecting screen.
The most effective remedy for decrease in thermal losses is fastening to a surface
behind radiators of a central heating: site of the heat reflecting screen.
The combined material of a product has double effect of saving of heat from radiators
of a central heating:


heat reflecting an effect: foil reflects to 97% of the thermal radiation of
radiators, thermal devices, etc. falling on a screen surface;
heat-insulating effect: at the expense of low coefficient of heat
conductivity of the made foam polyethylene, heat conductivity
makes 0,034 W / мК. A limit temperature interval of operation of the
heat reflecting screen: from-60 to +100 degrees Celsius. At operation the
screen doesn't allocate harmful substances.



9. Isolation of bodies automobile and trucks

 

10. Isolation of refrigeration units






Catalogue